Flammable vs. Combustible: Which Pipe Label Color?
Short answer: under ASME A13.1, pipes carrying flammable fluids get a yellow marker with black lettering, and pipes carrying combustible fluids get a brown marker with white lettering. The tricky part is deciding which category a fluid belongs in, because OSHA, NFPA, and ASME A13.1 don't define "flammable" and "combustible" the same way.
Getting it wrong is common. A pipe of fuel oil or hot process oil can be "combustible" on one document and "flammable" on another. This guide explains the definitions, how A13.1 sorts fluids for pipe marking, and how to label your lines with confidence.
Why the Right Color Matters
Pipe marker colors tell people about the hazard before they read a word:
- Maintenance crews know whether a line can feed a fire before they open or cut it.
- Firefighters and emergency responders can read the hazard from a distance.
- Contractors and new hires get the same message as your experienced staff.
- A consistent color scheme makes audits and insurance inspections go smoother.
Flammable vs. Combustible at a Glance
| # | Topic | What to Know |
|---|---|---|
| 1 | ASME A13.1 colors | Flammable fluids: safety yellow background, black legend. Combustible fluids: safety brown background, white legend. |
| 2 | ASME A13.1 definitions | Flammable fluids are vapors, or produce vapors, that can ignite and keep burning in air under ambient or expected operating conditions. Combustible fluids can burn but are not flammable. |
| 3 | OSHA 29 CFR 1910.106 | Any liquid with a flashpoint at or below 199.4°F (93°C) is a flammable liquid, in Categories 1 through 4. OSHA no longer uses "combustible liquid" in this standard. |
| 4 | NFPA 30 | Flammable (Class I) liquids have a flashpoint below 100°F (37.8°C). Combustible (Class II and III) liquids have a flashpoint at or above 100°F. |
| 5 | Service conditions | A13.1 looks at the fluid as it runs in your pipe, so a combustible liquid that is heated in service can belong under the flammable color. |
Topic 1: The ASME A13.1 Color Scheme
ASME A13.1 is the pipe identification scheme most U.S. facilities follow. It assigns a background and lettering color by the hazard of the contents. Brown with white lettering was added for combustible fluids in the 2007 edition, which is why older facilities often have combustible lines still marked in yellow or green.
- Flammable fluids: yellow background, black legend.
- Combustible fluids: brown background, white legend.
- Toxic and corrosive fluids: orange background, black legend.
- Fire-quenching fluids: red background, white legend.
- Water: green background, white legend. Compressed air: blue background, white legend.
Recent editions group flammable and oxidizing fluids together under yellow and black. The latest edition we have found is ASME A13.1-2023.
Yellow and black means flammable; brown and white means combustible.
Topic 2: Why the Definitions Don't Match
Three sources use the same words in different ways, and your SDS, fire code, and pipe markers may each follow a different one.
- OSHA aligned 29 CFR 1910.106 with the Globally Harmonized System (GHS) in 2012. Every liquid with a flashpoint at or below 199.4°F is now a "flammable liquid," split into four categories.
- NFPA 30 still uses both terms: below 100°F is flammable, 100°F and above is combustible.
- ASME A13.1 doesn't use a flashpoint cutoff. It asks whether the fluid, under ambient or expected operating conditions, gives off vapor that can ignite and continue to burn in air.
- Because of this, a liquid OSHA calls a Category 4 flammable liquid may still be a combustible (brown) fluid for pipe marking at room temperature.
The standard itself notes that its flammable category can apply to fluids defined elsewhere as either flammable or combustible, depending on service conditions.
Don't pick the color from the SDS label alone; look at how the fluid behaves inside your pipe.
Topic 3: How to Classify a Line
Use a simple, repeatable process so every line in your facility is classified the same way.
- Pull the SDS for the contents and note the flashpoint and physical state.
- Check the line's operating temperature and pressure. A liquid heated near or above its flashpoint behaves like a flammable fluid.
- Gases and fluids that readily give off ignitable vapor, like natural gas, propane, and gasoline, get yellow and black.
- Liquids that can burn but don't give off ignitable vapor in service, like many lubricating and hydraulic oils at normal temperatures, get brown and white.
- When a line is borderline, use the more protective (flammable) color and document why.
Write your decisions down in a pipe marking schedule so the next person who adds a line labels it the same way.
Classify by flashpoint and operating conditions, then record the decision.
Topic 4: The Rest of the Marker
Color is only part of a compliant pipe marker. ASME A13.1 requires color to be used together with a written legend.
- Use the name of the contents as the legend, such as "Fuel Oil" or "Natural Gas."
- Add flow arrows so responders know which way the fluid is moving.
- Size the marker and lettering to the pipe's outside diameter.
- Place markers so they are visible from the normal approach, including near valves, wall penetrations, and changes in direction.
- GHS pictograms are optional, not mandatory, but can add useful hazard detail.
For steam lines and other user-defined colors, see our article on steam pipe marking colors.
A good marker shows the color, the contents, and the direction of flow.
Topic 5: Updating Older Markers
Many facilities still have combustible lines marked yellow, or older green-and-white markers from before the 2007 color changes.
- Walk your piping and list every marker that doesn't match the current scheme.
- Replace faded, peeling, or unreadable markers at the same time.
- Mark abandoned piping, which A13.1 recommends identifying with a white background and black lettering.
- Re-check markers whenever contents, temperature, or flow direction change.
Kasama can audit and re-mark your lines, or supply the printer and supplies to make ANSI pipe markers in-house.
An audit catches outdated colors before an inspector or a responder does.
Free Guide: ANSI Pipe Marking
Colors, marker sizes, and placement for ASME A13.1 pipe marking in one PDF.
